View 81006_477851.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

REVISIONS LTR F G H DESCRIPTION Add peak current to absolute maximum ratings. Editorial changes throughout. Changes in accordance with NOR 5962-R144-95. Make corrections to the switch operation table in 3.3.1. Update boilerplate to reflect current requirements. -rrp DATE (YR-MO-DA) 92-11-24 95-10-20 03-03-10 APPROVED M. A. FRYE M. A. FRYE R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV SHEET REV SHEET REV STATUS OF SHEETS PMIC N/A REV SHEET PREPARED BY Gary J. Zahn H 1 H 2 H 3 H 4 H 5 H 6 H 7 H 8 H 9 H 10 H 11 H 12
STANDARD MICROCIRCUIT DRAWING
THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE
CHECKED BY William E. Sharp
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 http://www.dscc.dla.mil
APPROVED BY N. A. Hauck
MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL ANALOG SWITCHES WITH DRIVERS, MONOLITHIC SILICON
DRAWING APPROVAL DATE 81-10-01
AMSC N/A
REVISION LEVEL H
SIZE A SHEET
CAGE CODE
14933
1 OF 12
81006
DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
5962-E243-03
1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 81006 01 X X
Drawing number
Device type (see 1.2.1)
Case outline (see 1.2.2)
Lead finish (see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 Generic number IH5040, DG5140 IH5041, DG5141 IH5042, DG5142 IH5043, DG5143 IH5044, DG5144 IH5045, DG5145 IH5046 IH5047 IH5140, HI5040 IH5141, HI5041 IH5142, HI5042 IH5143, HI5043 IH5144, HI5044 IH5145, HI5045 HI5046 IH5047, HI5047 HI5046A HI5047A IH5148, HI5048 IH5149, HI5049 IH5150, HI5050 IH5151, HI5051 Circuit function One-channel, 75 ohms, SPST switch Two-channel, 75 ohms, SPST switch One-channel, 75 ohms, SPDT switch Two-channel, 75 ohms, SPDT switch One-channel, 75 ohms, DPST switch Two-channel, 75 ohms, DPST switch One-channel, 75 ohms, DPDT switch One-channel, 75 ohms, 4PST switch One-channel, 75 ohms, SPST switch Two-channel, 75 ohms, SPDT switch One-channel, 75 ohms, SPDT switch Two-channel, 30 ohms, SPDT switch One-channel, 30 ohms, DPST switch Two-channel, 75 ohms, DPST switch One-channel, 75 ohms, DPDT switch One-channel, 75 ohms, 4PST switch One-channel, 30 ohms, DPDT switch One-channel, 30 ohms, 4PST switch Two-channel, 30 ohms, SPST switch Two-channel, 30 ohms, DPST switch One-channel, 30 ohms, SPDT switch Two-channel, 30 ohms, SPDT switch
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter A E I 2 X Descriptive designator GDFP5-F14 or CDFP6-F14 GDIP1-T16 or CDIP2-T16 MACY1-X10 CQCC1-N20 CDFP3-F14 Terminals 14 16 10 20 14 Package style Flat pack Dual-in-line Can Square leadless chip carrier Flat pack
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
2
1.3 Absolute maximum ratings. V+ - V- .................................................................................... V+ - VD ................................................................................... VD - V- .................................................................................... VD - VS .................................................................................... VL - V-..................................................................................... VL - VIN ................................................................................... VL - VR .................................................................................... VIN - VR ................................................................................... VR - V- .................................................................................... VR - VIN ................................................................................... Current (any terminal except S or D)...................................... Peak current (source to drain) 1/........................................... Storage temperature range .................................................... Lead temperature (soldering, 10 seconds) ............................ Junction temperature (TJ)....................................................... Power dissipation, (PD) 2/: Cases A and X at TA = +125C .......................................... Case E at TA = +125C ...................................................... Case I at TA = +125C ........................................................ Case 2 at TA = +125C ....................................................... 1.4 Recommended operating conditions. +VCC ...................................................................................... -VCC ....................................................................................... VR .......................................................................................... VL .......................................................................................... +15 V dc -15 V dc 0 V dc 5 V dc 33 V dc 30 V dc 30 V dc 22 V dc 33 V dc 30 V dc 20 V dc 20 V dc 33 V dc 2 V dc 30 mA 80 mA -65C to +150C +300C +175C 350 mW 400 mW 350 mW 350 mW
Ambient operating temperature range (TA) ............................ -55C to +125C Thermal resistance, junction-to-case (JC) ............................. See MIL-STD-1835 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 MIL-STD-1835 Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines.
1/ Pulse at 1 ms, 10 percent duty cycle maximum. 2/ For TA = +100C to +125C, derate linearly at 12 mW/C.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
3
HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 -- List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.3.1 Switch operation. The analog switches listed below are guaranteed to turn "on" with either a "low" input (VR VIL 0.8 V) or "high" input (2.4 V VIH VIL) as specified below (see figure 1). Device types 01, 09 02, 10, 05, 13, 19 03, 11, 21 04, 12, 22 07, 15, 17 06, 08, 14, 16, 18, 20 VIN 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc 2.4 V dc 0.8 V dc Channels ON 1 1, 2 1 2 1, 2 3, 4 2, 3 1, 4 1, 2, 3, 4 1, 2 2 1 3, 4 1, 2 1, 4 2, 3 1, 2, 3, 4 Channels OFF 1
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
4
TABLE I. Electrical performance characteristics. Conditions -55C TA +125C VCC = 15 V unless otherwise specified VD = -10 V, IS = 10 mA,
Test
Symbol
Group A subgroups
Device type Min
Limits
Unit
Drain source "ON" resistance
RDS
1, 3 2 1, 3 2
1 - 16 17 - 22 1 - 16 17 - 22 All
Max 75 150 45 50 75 150 45 50 75 150 75 150
1/
VD = 10 V, IS = -10 mA,
1, 3 2 1, 3 2
VD = -7.5 V, IS = 10 mA, VCC = 10 V VCC = 10 V Channel "ON" leakage current ID(ON) 2/ 2/ VD = 7.5 V, IS = -10 mA, VS = VD = 10 V, See 3.3.1 for VIN VS = VD = -10 V, See 3.3.1 for VIN Drain "OFF" leakage current ID(OFF) VS = -10 V, VD = 10 V, See 3.3.1 for VIN VS = 10 V, VD = -10 V, See 3.3.1 for VIN Source "OFF" leakage current IS(OFF) VS = 10 V, VD = -10 V, See 3.3.1 for VIN VS = -10 V, VD = 10 V, See 3.3.1 for VIN Input current, input voltage low Input current, input voltage high Positive supply current IIL IIH +ICC VIN = 0 V VIN = 2.4 V, 5 V VIN = 0 V, 5 V
1, 3 2 1, 3 2 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1 1, 3 2 1, 3 2 1, 3 2 1 2, 3
All
-200 -2 -200 -2
200 2 200 2 100 1 100 1 100 1 100 1 1 1 1 10 10 100 200 300
nA
All
-100 -1 -100 -1
nA
All
-100 -1 -100 -1
nA
All All 1-8 9 - 22 1-8 9 - 22
-1 -10 -1 -1
A A A
Negative supply current
-ICC
VIN = 0 V, 5 V
1, 3 2 1 2, 3
-10 -100 -200 -300
A
See footnotes at end of table.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
5
TABLE I. Electrical performance characteristics - Continued. Conditions -55C TA +125C VCC = 15 V unless otherwise specified VIN = 0 V, 5 V
Test
Symbol
Group A subgroups
Device type Min
Limits
Unit
Logic supply current
+IL
1, 3 2 1 2, 3
1-8 9 - 22 1-8 9 - 22 1-8 -10 -100 -200 -300
Max 10 100 -200 -300
A
Reference supply current
+IR
VIN = 0 V, 5 V
1, 3 2 1 2, 3
A
Turn-on time
tON
11 9 10 11 9 10
375 450 550
ns
9 - 22
450 500 800
Turn-off time
tOFF
11 9 10 11 9 10
1-8
250 250 400
ns
9 - 22
350 450 600
Single channel isolation 2/
VISO
RL = 100 , f = 100 kHz, VIN = 2 VP-P, CL = 5 pF, TA = +25C RL = 100 , f = 100 kHz, VIN = 2 VP-P, CL = 5 pF, TA = +25C VIN = 0 V, CL = 10 nF, TA = +25C TA = +25C
9
All
60
dB
Crosstalk between channels 2/
VCT
9
All
60
dB
Charge transfer error
2/
VCTE
9 9
All 03, 04, 07 All All 5
30
mV ns
Break before make time delay 2/ Driver input capacitance 2/ Switch input capacitance 2/ Switch output capacitance 2/
tD
CA CIS
VIN = 0 V, TA = +25C Switch off, TA = +25C
9 9
45 60
pF pF
COS
Switch off, TA = +25C
9
All
60
pF
1/ The listed resistance limits correspond to the following voltage values: 45 and 75 - 9.25 V, 6.75 V 50 and 150 - 8.50 V, 6.0 V 2/ If not tested, shall be guaranteed to the limits specified in table I herein.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
6
Device type 01 Case outline A
Device types 01 and 09 Case outline E
Device type 09 only Case outline I
Device type 02 Case outline A
Device types 02 and 10 Case outline E
Device type 19 Case outline E
FIGURE 1. Terminal connections.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
7
Device types 02 and 10 Case outline I
Device type 03 Case outline A
Device types 03, 11, and 21 Case outline E
Device type 04 Case outline A
Device types 04, 12, and 22 Case outline E Case outline 2
FIGURE 1. Terminal connections - Continued.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
8
Device type 05 Case outline A
Device types 05 and 13 Case outline E Case outline I
Device type 06 Case outline A and X
Device types 06, 14, and 20 Case outline E Case outline 2
FIGURE 1. Terminal connections - Continued.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
9
Device type 07 Case outline A
Device types 07, 15, and 17 Case outline E
Device type 08 Case outline A
Device types 08, 16, and 18 Case outline E
FIGURE 1. Terminal connections - Continued.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
10
3.5.1 Certification/compliance mark. A compliance indicator "C" shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator "C" shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. b. Tests shall be as specified in table II herein. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
11
TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) ---1*, 2, 3 1, 2, 3, 9, 10, 11 1
Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) * PDA applies to subgroup 1. 4.3.2 Groups C and D inspections. a. b.
End-point electrical parameters shall be as specified in table II herein. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. TA = +125C, minimum. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
(2) (3)
5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234 APR 97
SIZE
A
REVISION LEVEL
81006
SHEET
H
12
STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 03-03-10 Approved sources of supply for SMD 81006 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535.
Standard microcircuit drawing PIN 1/ 8100601AA 8100601EA 8100602AA 8100602EA 8100602IA 8100603AA 8100603EA 8100604AA 8100604EA
Vendor CAGE number 3/ 1ES66 3/ 3/ 1ES66 3/ 3/ 3/ 1ES66 3/ 3/ 3/ 1ES66 3/
Vendor similar PIN 2/
Reference military specification PIN M38510/10501BAA M38510/10501BEA M38510/10502BAA
IH5040MJE/883B DG5140AK IH5041MJE/883B DG5141AK DG5141AA IH5042MJE/883B DG5142AK
M38510/10502BEA M38510/10502BIA M38510/10503BAA M38510/10503BEA M38510/10504BAA
IH5043MJE IH5043MJE/883B DG5143AK
M38510/10504BEA
8100605AA 8100605EA 8100605IA 8100606AA 8100606EA 8100606XC 8100607AA 8100607EA 8100608AA 8100608EA 8100609EA 8100609IA
3/ 1ES66 3/ 3/ 3/ 1ES66 3/ 1ES66 3/ 3/ 3/ 1ES66 1ES66 3/ 3/ IH5047MJE/883B IH5140MJE/883B HI1-5040/883 IH5044MJE/883B DG5144AK DG5144AA IH5045MFD/883B IH5045MJE/883B DG5145AK IH5045MFD/883B
M38510/10505BAA M38510/10505BEA M38510/10505BIA M38510/10506BAA M38510/10506BEA
M38510/10507BAA M38510/10507BEA M38510/10508BAA M38510/10508BEA M38510/10501BEA M38510/10501BIA
See footnotes at end of table.
1 of 3
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. Standard microcircuit drawing PIN 1/ 8100610EA Vendor CAGE number 1ES66 3/ 34371 8100610IA 8100611EA 3/ 1ES66 3/ 34371 8100612EA 1ES66 3/ 34371 81006122A 8100613EA 34371 1ES66 3/ 3/ 8100613IA 8100614EA 3/ 1ES66 3/ 3/ 81006142A 8100615EA 8100616EA 8100617EA 8100618EA 8100619EA 3/ 3/ 1ES66 3/ 34371 3/ 3/ 3/ See footnotes at end of table. IH5145MJE/883B IH5145MJE HI1-5045/883 HI4-5045/883 HI1-5046/883 IH5047MJE/883B HI1-5047/883 HI1-5046A/883 HI1-5047A/883 IH5148MJE/883B HI1-5048/883 --------M38510/10507BEA M38510/10508BEA IH5142MJE/883B IH5142MJE HI1-5042/883 IH5143MJE/883B IH5143MJE HI1-5043/883 HI4-5043/883 IH5144MJE/883B IH5144MJE HI1-5044/883 M38510/10505BIA M38510/10506BEA --M38510/10505BEA M38510/10504BEA Vendor similar PIN 2/ IH5141MJE/883B IH5141MJE HI1-5041/883 M38510/10502BIA M38510/10503BEA Reference military specification PIN M38510/10502BEA
2 of 3
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
Standard microcircuit drawing PIN 1/ 8100620EA 81006202A 8100621EA 8100622EA
Vendor CAGE number 1ES66 3/ 3/ 1ES66 3/ 3/
Vendor similar PIN 2/ IH5149MJE/883B HI1-5049/883 HI4-5049/883 IH5150MJE/883B HI1-5050/883 IH5151MJE
Reference military specification PIN ---------
34371 1ES66 81006222A 34371
HI1-5051/883 IH5151MJE/883B HI4-5051/883 ---
1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 1ES66 Vendor name and address Maxim Integrated Products 120 San Gabriel Drive Sunnyvale, CA 94086 Intersil Corporation 2401 Palm Bay Blvd P.O. Box 883 Melbourne, FL 32902-0883
34371
The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.
3 of 3

▲Up To Search▲

Price & Availability of 81006

	To Download 81006 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .